Stretching and Mounting

For a downloadable file to print about WET stretching and mounting, click Stretching and Mounting.pdf

 

For a downloadable file to print about DRY stretching and mounting, click Dry Mount Method.pdf

 

Painting your sumi-e masterpiece is only half of the project. Rice paper is not sized, meaning it does not contain stiffeners or sizing that help protect the paper from wrinkles and shrinkage. Lack of sizing is what gives rice paper the properties that allow ink and paint to blend or bleed, creating the unique look of sumi-e painting. To be preserved wrinkle-free, your painting must now be stretched and mounted onto special backing paper before it can be framed and displayed.

 

TRADITIONAL WET STRETCHING AND MOUNTING

 

Here are the supplies you will need, and basic directions for traditional wet-style stretching and mounting. If you are new to stretching and mounting, it is best to try it first at a workshop or under the supervision an experienced sumi-e painter. Practice first on a painting that is not your masterpiece but is painted on the same paper with the same ink and paints.

 

Supplies:

  • Mounting paper

  • Mounting surface/board (smooth, clean formica, glass, plexiglass, masonite, wood;

        The mounting surface/board must be at least 5” larger than your painting, length and width)

  • Wheat paste (Yasutomo Nori)

  • Alum

  • 2 wide brushes (3” or 4”)

  • Plastic bristle brush (ton ton)

  • Blue masking tape

  • Paper towels

  • Small spray bottle with water

  • Krylon fixative or hair spray

 

Procedure:

  1. Cut the mounting (backing) paper so it is about 1 inch larger than your painting on all sides,

  2. Mix about 2 Tablespoons (3 squeezes) of wheat paste and 1/4 teaspoon alum in about 2/3 cup warm water. Completely dissolve all the lumps.

  3. If your painting has very colorful areas, lightly spray (OUTDOORS) with Krylon or hair spray on these areas (this prevents the color from bleeding).

  4. Place your painting face down on a clean mounting surface.

  5. Use a wide, thin, soft brush (hake type), covered well in the glue solution to cover the back of the painting with an even coat of glue. START PAINTING FROM THE CENTER OUT, little by little, working the wrinkles and bubbles out to the edges. Paper will be very wet.

  6. Wipe off excess glue around the painting, so the exposed mounting surface is clean. Pick off any brush hairs or lint.

  7. Place the rough side of the mounting paper over the painting, centering it so there is a 1 inch border all around. Line it up along one edge, then let it drape down.

  8. Brush with a wide DRY brush from the middle of the painting out to the edges.

  9. Spray lightly and evenly with water all over the rice paper, then brush again with the dry brush from the center out. NOTE: When brushing, use some pressure, but be sensitive not to tear or damage the paper. Some paper is very fragile, especially when wet.

  10. Lay a couple of layers of paper towel over the painting and pound with the ton ton, all over. This will absorb some of the moisture, and adheres the 2 papers.

  11. Lift a corner of the paper and peel the picture away from the surface at an angle, not straight up and lay it down face up (either on the same surface or another one).

  12. Again put paper towels on the picture and brush with a large, soft, dry brush to draw out more moisture.

  13. Tape the edges of the painting down all the way around. Allow it to dry like this for several hours to 2 days, depending on the weather. Do not let it dry in the wind or sun. Indoors is best.

  14. Remove the tape and it is ready for framing, wrinkle free.

NOTE: A painting can also be left to dry face down. If you do this skip Step #11 and #12.

NOTE: While your painting is still wet, and you see a hair or bubble or something under your picture, you can prick a hole over it with a pin, then extract the particle with a tweezer, then tap the hole closed with your finger.

DRY STRETCHING AND MOUNTING

 

Supplies:

Finished art piece, glue sheet cut exact same size as art piece, iron with steam function, backing board cut about 1" larger than art (Matt board is good), denim fabric (enough to have 4 layers of fabric for the ironing area), sheet of clean paper larger than art, spray bottle with water.

 

Prep:

  1. Spray art with very light amount of water on face up side (set aside few minutes)

  2. Set iron to wool/cotton setting (slight steam)

  3. Lay out denim 4 layers thick on flat firm surface large enough to lay art

  4. And have hot iron near this surface

  5. Cut glue sheet exactly same size as art piece

  6. Cut backing board 1" larger than art piece

 

Assemble glue sheet:

  1. Place cut glue sheet with glue face up on denim surface

  2. Place art face up on glue sheet matching edges of art with glue sheet edges

  3. (Caution - check to be sure art piece is face up)

  4. Cover with sheet of clean paper

  5. Iron slowly from center going out to edges beginning with center to top section

 

Assemble to backing:

  1. Remove glue sheet backing from art piece (little wrinkles ok)

  2. Place backing Matt board on denim smooth side up

  3. Place art face up in center of matt board

  4. Cover with clean sheet paper

  5. Iron slowly from center out

 

Copyright Notice:  This site is owned and operated by Friends of Taka Sumi-e and www.takasumi-e.com

All images are copyrighted and may not be used without permission of the artists. All rights reserved.